8.2 KiB
8.2 KiB
/interface bridge port set [find] horizon=none
/interface wireless set wlan1 default-forwarding=yes
/interface wireless set wlan1 multicast-helper=full
/interface bridge port set [find interface="wlan1"] hw=no
Command | Explanation |
---|---|
1. Create a Bridge Interface | |
/interface bridge add name=bridge protocol-mode=none |
Creates a bridge named bridge with protocol mode set to none for transparent bridging. |
2. Add Interfaces to the Bridge | |
/interface bridge port add bridge=bridge interface=ether1 |
Adds ether1 to the bridge. |
/interface bridge port add bridge=bridge interface=ether2 |
Adds ether2 to the bridge. |
/interface bridge port add bridge=bridge interface=wlan1 |
Adds the Wi-Fi interface wlan1 to the bridge. |
3. Configure the Wireless Interface | |
/interface wireless set wlan1 mode=ap-bridge |
Sets wlan1 to access point mode to allow multiple clients. |
/interface wireless set wlan1 ssid="YourSSID" |
Sets the Wi-Fi network name (replace "YourSSID" with your desired SSID). |
/interface wireless set wlan1 frequency=auto |
Sets the Wi-Fi frequency to automatic selection. |
/interface wireless set wlan1 wireless-protocol=802.11 |
Ensures the standard Wi-Fi protocol is used. |
/interface wireless set wlan1 default-forwarding=yes |
Allows communication between wireless clients and the LAN. |
/interface wireless set wlan1 multicast-helper=full |
Enables full multicast forwarding for protocols that require it. |
4. Assign an IP Address to the Bridge | |
/ip address add address=192.168.1.1/24 interface=bridge |
Assigns IP 192.168.1.1 to the bridge interface (adjust as needed). |
5. Configure DHCP Server | |
/ip pool add name=dhcp_pool ranges=192.168.1.100-192.168.1.200 |
Creates a DHCP pool for clients. |
/ip dhcp-server add name=dhcp1 interface=bridge address-pool=dhcp_pool |
Adds a DHCP server on the bridge interface. |
/ip dhcp-server network add address=192.168.1.0/24 gateway=192.168.1.1 dns-server=8.8.8.8 |
Sets DHCP network parameters (adjust gateway and DNS as needed). |
6. Adjust Bridge Settings | |
/interface bridge set bridge protocol-mode=none |
Ensures no protocol-specific filtering on the bridge. |
7. Disable Hardware Offloading on wlan1 | |
/interface bridge port set [find interface="wlan1"] hw=no |
Disables hardware offload for wlan1 to improve multicast handling. |
8. Ensure ether2 Is Active (Optional) | |
/interface enable ether2 |
Enables ether2 if it is disabled. |
9. Check and Remove Bridge Filters (If Any) | |
/interface bridge filter remove [find] |
Removes any bridge filters to allow all Layer 2 traffic. |
10. Review Firewall Settings | |
/ip firewall filter print |
Displays current firewall rules. |
(If necessary) | |
/ip firewall filter remove [find] |
Removes all firewall filter rules (use with caution). |
11. Update RouterOS and Wireless Firmware (Recommended) | |
/system package update check-for-updates |
Checks for RouterOS updates. |
/system package update install |
Installs available updates. |
/interface wireless upgrade |
Upgrades wireless interface firmware. |
12. Reboot the Router | |
/system reboot |
Reboots the router to apply changes. |
13. Verify Wireless Interface Settings | |
/interface wireless print detail where name="wlan1" |
Displays detailed settings of wlan1 for verification. |
14. Adjust Wireless Data Rates (Optional) | |
/interface wireless set wlan1 basic-rates-b=1Mbps basic-rates-a/g=6Mbps |
Sets basic data rates to improve multicast traffic reliability. |